HomeInfo CenterKnow-howTYPES OF RUBBER MOLDING

TYPES OF RUBBER MOLDING

LIQUID INJECTION MOLDING: (LIM™)

The custom injection molding of Liquid Silicone Rubber (LSR)  uses much of the same process and equipment as does injection molding. In both processes, the mold is heated and closed before the uncured rubber is injected. Unlike high consistency rubber (HCR), also known as gum stock, liquid silicone is just that, a "high viscosity liquid" that comes in two parts, Part A and Part B. 

Both parts are liquid but one part contains the catalyst which is platinum. Liquid silicone has the consistency of cold molasses, is naturally translucent and comes in either pail kits (approx. 80 lbs) or drum kits (approx. 800 lbs) The two parts are mixed and delivered to the barrel of the injection press via a mixing/metering pumping system. If desired, Pigment may be added via a pumping system to color the liquid silicone. The mixed liquid silicone is then injected into the mold much like gum stock, but the RunnerGate and Sprue are generally smaller due to its lower Viscosity. Once in the mold, the liquid silicone cures at a much faster rate than typical high consistency silicone due to its platinum cure system. As a result of this rapid cure cycle, the part price is frequently lower than parts made using conventional molding processes such as Compression Transfer and Injection Molding

LIM™ is ideal for applications where contamination is a problem or where high volumes are required. The Medical Industry prefers LIM™ because it is a closed system of molding, meaning, the pail or drum kits of uncured Liquid silicone are loaded into the pumping system, injected and cured without human contact. Liquid Injection Silicone Molding is also ideal because of its ability to manufacture Silicone Products at a low cost thus ensuring competitiveness in the Medical Industry.

LSR machine 
Are you ready for us to assist you? Click here for a direct contact to KDL Precision Molding.

INJECTION MOLDING

In the case of Injection Molding, the rubber is supplied to the injection machines barrel & nozzle assembly on a continual basis. In this case, the rubber used is a high consistency Silicone rubber (HCR) known as "gum stock".

The gum stock is supplied to the injection barrel via a pressurized device called a "stuffing box".

The injection press closes the heated mold and applies pressure to keep the mold closed during the injection and curing cycles. The screw then injects the rubber through the nozzle into the mold. The rubber travels through the mold via a system of runners and sprues and finally enters the mold cavities through a Gate or gates. It then fills and packs the cavities to form the desired part. The rubber is heated by the mold and the friction of the ScrewRunnerSprue and Gate. The rubber then completes its cure cycle and is removed from the mold.

COMPRESSION MOLDING


Compression molding is the simplest form of thermal set molding. Compression molds vary considerably in size, shape, and complexity and also contain from one to a very high number of cavities. The compression molding process is as follows: An uncured rubber preform, which is often shaped to the approximate size & configuration of the desired finished part, is placed directly in the mold cavity prior to mold closure.



During the molding process, rubber is compressed (squeezed) between the Top and Bottom plates. The uncured pre-form must weigh more than the finished part in order for air to be driven out of the mold cavity during mold closure. If the preform weighs the same or less than the finished part; voids, air traps or nonfills will appear on the finished product. The excess rubber will flow into the overflow or flash groove. Two, three or more mold plates may be used depending upon part configuration and complexity. The rubber is then Vulcanized (cured) utilizing both heat and pressure. The end result is a Rubber Product that will meet your specifications.

TRANSFER MOLDING

Transfer molds also vary considerably in size, shape and complexity and may contain from one to a high number of cavities.

In the Transfer Molding Process the uncured rubber is not placed directly in the mold as in compression molding. Instead, it is placed in a Transfer Pot located above the cavity area. It is then pushed or transferred into the cavity by a Piston through a RunnerSprue and Gate system. The rubber is then vulcanized (cured) utilizing heat & pressure. Transfer molding is similar to Injection Molding because rubber enters the cavity after the mold is closed. A rubber part that is transfer molded may be less expensive than a part that is compression molded.

LSR01
LSR02
LSR03
LSR04
LSR05
LSR06
LSR07
LSR08
LSR09
LSR10
LSR11
LSR12
LSR13
LSR14
LSR15
LSR16
LSR17
LSR18
LSR19

Last Updated on Monday, 24 September 2012 09:23

Login Form

Contact us now

WEIXIN-CHINA
Add:  197-2-504, Hubin North Road, Xiamen, 361002, China
Tel:   +86-592-5561608
Fax:  +86-592-2031383

This email address is being protected from spambots. You need JavaScript enabled to view it.

Go to top